LT2P/IPSEC VPN Balance One

[soly]

Dear Sir/Madam

currently i used Peplink Balance One
WAN PPPOE: IP address http://103.x.x.x
Lan 192.168.1.0/24

please could you guide me about how to configure IPSEC VPN.
my mail [email protected].

Best Regards
from Soly

[Zach_Tangen]

Hello Soly,

We do have a few guides for setting up IPSec with a few devices and vendors.

Configure IPsec to Juniper SSG Firewall using X.509 Authentication

This guide covers configuration of IPSEC between Peplink and Juniper SSG firewall using X.509 authentication. The example assumes the following settings: IPSEC VPN Settings Peplink WAN IP Address: 210.211.10.5 Peplink LAN Network: 192.168.2.0/24 Peplink Certificate: Email: [email protected] Juniper SSG WAN IP Address: 66.80.3.1 Juniper SSG LAN Network: 192.168.1.0/24 Juniper Certificate: Email: [email protected] IPSEC Phase 1 Authentication: SHA-1 ISPEC Phase 1 Encryption: AES-128 ISPEC Phase 1 …

How to IPsec to the Cisco ASA 5505 v9.x Firewall Using Pre-shared Key Authentication

This guide covers configuring an IPsec VPN between Peplink and Cisco ASA firewall. The example assumes the following settings: IPSEC Network Simulation Diagram [image] IPsec VPN Settings Peplink WAN1 IP Address: 210.211.10.1/29 Peplink LAN Network: 192.168.30.0/24 Peplink LAN IP Address: 192.168.30.1/24 Cisco ASA WAN IP Address: 66.80.3.1/29 Cisco ASA LAN Network: 10.1.1.0/24 Cisco ASA LAN IP Address: 10.1.1.1/24 Mode: Main Pre Shared Key: password123 IPsec Phase 1 Authentication: SH…

Configure IPsec to a Juniper SSG Firewall

This guide covers configuration an IPsec VPN between Peplink and Juniper SSG firewall. The example assumes the following settings: IPsec VPN Settings Peplink WAN IP Address 210.211.10.5 Peplink LAN Network 192.168.2.0/24 Juniper SSG WAN IP Address 66.80.3.1 Juniper SSG LAN Network 192.168.1.0/24 IPsec Phase 1 Authentication SHA-1 ISPEC Phase 1 Encryption AES-128 ISPEC Phase 1 DH Group 2 IPsec Phase 2 Authentication SHA-1 ISPEC Phase 2 Encryption AES-128 ISPEC Phase 2 PFS Group 2 Configure Juni…

You’ll want to make sure that the encryption settings are matching on both the Peplink and the other vendors equipment. Your point of sale should be able to help you if you’re having issues setting up the other vendors router.

[mrkiasu]

it would be good idea to remove your public wan ip number, its expose to the internet now.

[TK_Liew]

@mrkiasu

it would be good idea to remove your public wan ip number, its expose to the internet now.

Good catch! It has been masked.

[soly]

Dear Zach_Tangen

i got it how to create IPSec VPN but after access vpn it need username and password
could you share me how to create username and password?

soly

[Zach_Tangen]

Are you trying to connect to the Balance using a computer or are you trying to create a connection using another router? If you’re using a computer, please confirm if you’re using L2TP and what client you are using.

[soly]

yes confirm using computer and create connect L2TP but after we connect connection need username and password for vpn. i would like to ask you how to create username and password for vpn client.

thanks from soly

[zegor_mjol]

I think you’ll find these instructions addressing your question:
https://forum.peplink.com/t/setting-up-l2tp-with-ipsec/8046

It is also covered on page 135 of the manual (section 12.14 - Remote User Access)

Cheers,

Z

[soly]

Dear Zegor_mjol

note with thanks it done for IPSEC VPN.

thanks
soly